Thursday 26 June 2014

June's Maintenance run

As part of the pre-season work up. XL231 had her monthly anti-det (anti deterioration) run on Sunday.  This was delayed by 2 weeks due to a snag with the APU Artouste engine that caused a bit of concern. Happily this turned out to be a partially sticking ADV (air delivery valve) that was soon cleared and the APU fuel control main solenoid valve was also removed and lubricated, as I was not happy with it.
Image
APU slight wet start!
As a partial ant-det run the week previous and to thoroughly test the APU, I briefed Rich on how to 'dry run' the main engines and he carried out his first engine turns successfully, with myself on the the external intercom and John inside controlling the APU and other systems from the AEO position.

The main anti-det runs were carried out with Ollie on the external comms, John in the back and myself in the Left hand seat. Young Sam was sitting in the co-pilots seat and I wet-ran the engines. Basically, putting fuel through the burners and out of the back as vapour without actually igniting it. This ensures the fuel system is never allowed to dry out and that the engine has been turned to ensure oil pressure and lubrication. John also checked all 4 main engine alternators were generating AC power. I then let Sam dry turn the engines and he did this very nicely for his first time. A dry-turn is a full spin, but without fuel being introduced and it helps to dry the fuel vapour in the jet pipes.

We then carried out full hydraulic functionals, exercising the flaps to all 3 positions, air brakes to the full range of full out & full in and the Ram Air Turbine scoops (RATs) on top of the rear fuselage. The nosewheel steering was also tested and the Flight Refuelling Hose Drum unit (HDU) lowered and raised several times.  The flying controls which are fully powered and self contained were then all tested. No snags were noted, apart from the Starboard RAT sticking in the open position occasionally.
Image
HDU lowered
Image
Anti-det run
XL231 is now waiting eagerly for her next outing.

Mainwheel Tyre change

After the last taxy run we noticed that one of the mainwheel tyres on the port side had lost part of its tread and was showing signs of de-laminating further.

As the taxy run was the last one of 2013 we decided to leave the tyre until into the following season, the tyre was holding pressure and was fine for standing the aircraft on and it did not interfere with engine runs and other winter/spring maintenance.

Now the season is here and pending taxy runs are on us, we decided to tackle that particular wheel this last weekend. As far as taxy runs go this has been a late start due to events around the site and the Tour De France coming through the area 5th/6th July.

The Victor and identical Vulcan mainwheels are a single wheel with twin tyres and are of a split rim construction. The first job is to ensure the tyres are deflated and the valves removed. The outer locking ring is removed and the outer tyre with its two sliding removable beads is taken off first. Usually this involves a lot of cursing and sweating, with large rubber mallets and pry bars. If the outer tyre is the culprit (as in this case) then the inner wheel can be left alone. However, an inner tyre means a full wheel strip down and it is hard work. Under the sliding beads and between the main rim and bead are large sealing O rings, these can get stuck to the sliding bead and are difficult to sometimes free up. Especially if the wheel has been built up for a considerable time. Fitting new tyres usually means changing the O rings as well (if they are available). If the O ring is flattened then its unlikely to be re-useable. We have found silicone grease is the best product to smear the O rings with in order to help seal and protect them.
Image
Outer tyre removed

Image
Ollie returning the wheel to Lindy 'wheelie good!'
Once the wheel is rebuilt it is then test inflated to check for leaks. Because there are so many seals the tendency for leaks is very real and likely. 100% leak free wheels are a rarity when you don't have access to most parts in a new condition.